OpenVox D130 Digital Card

OpenVox D130 is now the leading single port T1/E1/J1 PCI card in the open source industry.DE130 takes full advantage of Octasic® Hardware Echo Cancellation Module to deliver the superior voice quality over T1, E1, and J1 interface.It supports up to 32 channels in E1 mode or 24 channels in T1/J1 modes.

Industry 1st adjustable interrupt routing design
Interrupts frequency adjustment
Compatible with All Commercially Available Motherboards
Single T1/E1/J1 ports with PCI/PCI Express interface for high performance voice and data applications

The D130 is an upgrade product of the D115. It supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. D130 is supposed to be the most advanced single port T1/E1/J1 asterisk® card with superior quality in the open source community. The leading innovation ensures users to adjust the interrupts frequency to reduce the CPU load up to 70% and adjust the interrupt number to avoid interrupt number sharing or conflict.
D130 supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.
DE130 offers an Octasic® DSP-based echo cancellation module. The Octasic® DSP-based EC module enables users to eliminate echo tails up to 128ms or 1024 taps across all 32 channels in E1 mode or 24 channels in T1/J1 modes. Further, this module takes advantage of the Octasic® Voice Quality Enhancement to provide superior sound quality on all calls.
D130 works with Asterisk®, Elastix®, FreeSWITCH™, PBX in a Flash, trixbox®, Yate™ and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.

OpenVox Elastix&trixbox certified
Target Applications:

Voice-over Internet Protocol (VoIP) Services
Complex IVR Trees
"Meet-Me" Bridge Conferencing
Calling Card Platforms
VoIP Gateways (support SIP, H.323, and IAX)
Legacy PBX/IVR Services
Voice/Data Router (replace expensive routers)
PRI/Switch Compatibility - Network or CPE

Specifications

Voice-over Internet Protocol (VoIP) Services
Complex IVR Trees
"Meet-Me" Bridge Conferencing
Calling Card Platforms
VoIP Gateways (support SIP, H.323, and IAX)
Legacy PBX/IVR Services
Voice/Data Router (replace expensive routers)
PRI/Switch Compatibility - Network or CPE
Technical Specifications
Single T1/E1/J1 ports with PCI interface for high performance voice and data applications
Half-length PRI card
RJ48 connector
Low profile option
32 bit 33MHz PCI and fully PCI 2.3 compliant
32 bit bus master DMA data exchanges across PCI interface at 132 Mbytes/sec
Autosense compatibility with 5 V and 3.3 V PCI busses
FPGA design, upgradeable firmware onsite
Power: 2.43W Minimum, 6.1W Maximum at 3.3 V or 5 V.
Operation temperature: 0°C to 50°C
Storage temperature: -65°C to 125°C
Dimension: 2U Form factor: 12*6.4*1.8cm
Weight: 92g

Optional Octasic® DSP Echo Cancellation Module—EC2032:

128ms tail/channel (on all channel densities)
Octasic® Music Protection
Adaptive Noise Reduction
Automatic Level Control (G.169)
Field upgradeable algorithm
V.25 / V.8 answer tone (w/ and w/o phase reversal)
DTMF as per Q.24
No CPU load as a result of echo cancellation.
Does not increase the physical size of the card, and no additional slot is required
EC2032 power: 3.83W
Storage temperature: -40°C to 75°C

PRI Switch Compatibility

EuroISDN (PRI or PRA) - Q.931/Q.921
Network or CPE
AT&T 4ESS
National ISDN 2
CAS Voice Modes
DMS 100
Lucent 5E
Operating Systems: Linux (all versions, releases and distributions f rom 1.0 up)

Minimum Hardware Requirement:

800-Mhz Pentium III
128MB RAM
Available PCI Slot

OpenVox D130 Digital Card

D130 Digital Card OpenVox

Specifications

Documents

Certificates